Why Your EV Screen and the Charger Disagree on kWh
A customer rang me in October convinced a charging network was billing him twice. His car had told him the session delivered 41.2 kWh. The receipt on his card said 46.9 kWh.

A customer rang me in October convinced a charging network was billing him twice. His car had told him the session delivered 41.2 kWh. The receipt on his card said 46.9 kWh. He had screenshots of both, and he wanted me to write something he could send to the operator. I had to tell him the operator was almost certainly right, and so was his car, and that the two numbers were never measuring the same thing.
This comes up on maybe one in six installations I do now, usually a few weeks after the charger goes in, once the owner has started reading the screen properly. The gap is real, it is usually between 4 and 12 percent, and nobody at the dealership explains it because the people selling cars rarely know. Working out which number does what takes about ten minutes and saves a lot of pointless email.
Three meters, three different jobs
In a normal home setup there are three places a kilowatt hour figure comes from, and they sit at different points along the same cable.
Furthest upstream is your utility meter, or a sub-meter if your installer fitted one on the charger circuit. That device is legally sealed and tested, and it counts every unit that crosses into the house, including everything the charger and the car waste as heat. It is the only number your electricity supplier cares about.
Next is the charger's own meter. Hardwired units from most brands have one, and on public DC chargers it is a revenue grade meter that has to pass periodic verification. Depending on the unit, it reads either the AC going in or the DC going out to the car. That distinction matters more than anything else in this article, and the spec sheet almost never says which.
Last is the car. The figure on your infotainment screen or in the companion app is not from a meter at all. It is the battery management system reporting how much energy it believes reached the cells, worked out from pack voltage, current sensor readings and a temperature model. It is an estimate produced by software, and it is deliberately conservative, because the same model protects the pack.
So when the screen says 41.2 and the receipt says 46.9, the car is telling you what it stored and the charger is telling you what it sold. Both can be accurate.
Where the missing kilowatt hours actually go
The difference is not rounding. It goes somewhere, and on AC charging most of it goes into the onboard charger, the box in the car that converts your household alternating current into the direct current the pack needs. That conversion runs at roughly 88 to 94 percent efficiency depending on the unit and how warm it is. On a 40 kWh overnight session you lose 3 to 5 kWh there alone, and it leaves the car as heat through the vents under the hood.
Then there is thermal management. If the pack is at 2 degrees when you plug in, the car will spend its first twenty minutes warming the cells before accepting serious current, and on some models it does that from the wall rather than from the battery. In January I measured a car drawing 1.4 kW for nineteen minutes with the state of charge not moving at all. That energy is on your bill and nowhere on the car's session summary.
Cabin preconditioning does the same thing on a larger scale. A resistive heater pulling 4 kW for fifteen minutes before a scheduled departure is a kilowatt hour gone, and the car counts it as climate use, not charging.
Finally there is the overhead nobody budgets for. A plugged-in car keeps its communication module and contactors alive, and most units sit somewhere between 5 and 15 watts idle. Over a month of being plugged in most nights that is a rounding error on your bill, but it is the reason a session that ended at 3 a.m. shows a few more units at 7 a.m.
How big the gap should be before you worry
Here is what I use as a rough sanity check on residential jobs. These are measured from a sub-meter on the charger circuit compared against what the car reported, across the installs where I bothered to follow up.
| Situation | Typical gap, wall versus car | What it means |
|---|---|---|
| AC charging, mild weather, 7 kW | 7 to 10 percent | Normal onboard charger losses |
| AC charging, pack below 5 degrees | 12 to 20 percent | Normal, plus preheating from the wall |
| AC charging at 2.3 kW on a wall plug | 14 to 22 percent | Fixed overheads spread over a slow trickle |
| Public DC, 50 kW and up | 2 to 5 percent | Conversion happens in the charger, not the car |
| Any session, gap above 25 percent | Not normal | Loose termination, failing onboard charger, or the meter is reading another circuit |
That last row is the one worth acting on. A gap that wide on a warm night means energy is turning into heat somewhere it should not, and the usual culprit is a termination I can find in five minutes with a thermal camera. Twice it has been a shared neutral picking up another load. Once it was a sub-meter installed around the wrong conductor, which I would rather not talk about.
The advice to ignore the car screen is wrong
The standard response on owner forums is that the car's number is fiction and you should only ever trust the wall. I hear a version of this from installers too, and it throws away the more useful of the two figures.
The car's estimate is the only one that says anything about the health of the pack. Energy from the wall varies with weather, cable length and how cold the garage is. Energy into the cells, measured between two known states of charge, is close to a repeatable test. Log it monthly at the same two percentages and a slow decline is the earliest signal of capacity loss you will get without a dealer tool. One owner in Bergen has logged every session since 2019 and can show you his degradation curve with three bumps in it, all of them summers he fast charged heavily.
The right split is simple. Use the wall figure for money, because that is what you pay for. Use the car figure for condition, because that is what the pack is doing. Comparing them against each other is only useful as a fault check, not as an argument about who is cheating.
The same logic applies to the efficiency readout in kWh per 100 km. That number is taken from energy out of the pack, so it will always look better than what your bill supports. Dividing your monthly charger total by your monthly distance gives the honest figure, and on my own van it is 19 percent worse than what the dash claims.
What to check on your own setup this week
Do this over two sessions, in the same weather, and you will know your car's real conversion overhead rather than a number from a brochure.
- Note the charger's lifetime total before and after one full overnight session. If your unit does not show one, the app history usually does.
- Write down the car's reported session energy and the start and end state of charge from the same session.
- Divide the car's figure by the charger's figure. Anything from 0.80 to 0.93 on AC is unremarkable.
- Repeat on a cold night. The drop tells you what preconditioning is costing you, and whether a scheduled departure time is worth setting.
If you want the money side nailed down properly, read what a home charge actually costs once losses are included before you build a spreadsheet, because tariff windows move the answer more than efficiency does. And if your numbers look strange because sessions keep ending early, that is a different problem, covered in why a home charger keeps tripping the breaker.
One habit worth forming: screenshot the session summary on any public charger priced above about 0.55 euro per kWh. When an operator bills a stuck session for six hours of idle fees, the car's own timestamp settles it. The kWh argument you will lose. The duration argument you will win. The rest of our infotainment coverage goes through the screens feature by feature.
FAQ
Is my car under-reporting on purpose?
No, but it is reporting conservatively by design. The battery management system would rather understate stored energy than overstate it, because the same model decides how hard to push the pack. Treat it as a careful lower bound.
Why is the gap smaller at a public fast charger?
Because a DC charger does the conversion in its own cabinet and feeds direct current straight to the pack. The losses still happen, they just happen on the operator's side of the meter in some pricing models, which is part of why DC energy costs more per unit.
Should I fit a sub-meter on the charger circuit?
If you claim the charging back from an employer, or you are on a tariff that pays differently for EV load, yes. Expect to pay around 90 to 160 euro for the meter and an hour of labour. For simple curiosity, the charger's own counter is close enough.
Does a longer cable change the numbers?
Slightly, and less than people think. A 7.5 metre portable lead at 32 amps loses well under one percent compared with a 3 metre one. Cable length matters for heat and voltage drop at the far end of a long run, not for your bill.
More in Infotainment
Infotainment
Why Your EV Backup Camera Lags and How to Fix It
A reader sent me a clip in September that I have now watched about thirty times.
Infotainment
Wired CarPlay Not Connecting in an EV and the Cable Fix
You plug your iPhone into the USB port under the dash, the phone shows the charging icon, and the car screen does nothing.
Infotainment
EV Bluetooth Audio Skipping and How to Find the Cause
The bug report I hear most from EV owners is not about range or charging.